A 12-volt plug that looks exactly like a 24-volt one, a pin that switches on trailer fog lights, and the standards that sort out the rest.
North America has no formal standard for car and light truck trailer plugs, relying on flat 4-pin and round-blade 7-pin connectors, while Europe uses ISO 1724 7-pin and newer ISO 11446 13-pin plugs. Heavy vehicles use SAE J560 in North America and 24-volt ISO plugs in Europe.
Two seven-pin trailer plugs can be physically identical and still do very different things. The SAE J560 plug on North American heavy trucks has the same shape as the ISO 1185 plug used on European heavy vehicles, yet one is built for 12 volts and the other for 24, so joining them without a voltage converter is asking for trouble.
That is the tidy end of a messy business. Trailer plugs in North America and Europe grew up under different rules, with different pin counts and different wiring habits, and the difference between a 7-pin and a 13-pin plug is only the start of it.
What does a trailer connector do?
A trailer connector is the electrical link between a towing vehicle and the trailer behind it. It carries the signals that give the trailer its lights and, on some trailers, control over its brakes or other equipment. Which standard applies depends on the region and on whether the vehicle is a light car or a heavy truck.
One basic contrast runs through everything. In North America, and most commonly in the United States, brake lights and turn signals are very often combined on a single circuit. European wiring tends to keep stop lamp and indicators on separate circuits, which is why converters exist to connect a car wired the European way to a trailer wired the North American way.
The plug fits, but the voltage does not.
Which trailer plugs are used in North America?
For cars and light trucks there is no formal standard. What exists is an accepted standard, and the advice that goes with it is blunt: do not be entirely sure a vehicle and trailer fit until you have measured both connectors. Colour coding varies too, so colours quoted in a guide cannot be trusted without checking the actual contacts and wiring. In a flat 4-pin or 5-pin plug, it is fairly obvious which colour goes to which pin.
Light vehicles use a great many contacts, but two dominate: the flat 4-pin and the round-blade 7-pin. Unified outlets on the market combine the two into a single module.
The flat 4-pin and 5-pin
The flat 4-pin ranks among the commonest plugs on trucks in North America. It carries the minimum signals needed to meet regulatory requirements in the United States and is often used for simpler trailers. The flat 5-pin is rarer but compatible: a towing vehicle with a 5-pin outlet can take a trailer with a 4-pin plug. The spare wire commonly disables surge brakes while the trailer reverses.
The round-blade 7-pin and the 6-pin
The 7-pin round blade connector, governed by SAE J2863, the Automotive Trailer Tow Connector standard, is common on RVs and other large trailers that carry extra loads beyond tail lights, brake lights and turn signals. A 6-pin round connector turns up on medium-duty trailers that have both reversing lights and electric brakes.
The odd ones
Several less common plugs exist, and their wiring may not match any listing. A 6-pin rectangular connector has its pins in two rows, so it will not mate with the 4-pin and 5-pin flat plugs. A 5-pin round connector is wired like the 6-pin round without the centre reversing lamp pin. A 4-pin round connector survives on older truck and SUV set-ups, and trailers that need it have no braking system of their own and simply stop with the towing vehicle. A 3-pin round connector to DIN9680 was introduced by John Deere for farm equipment and has since been used on yachts and general electric cables. Two plugs that resemble SAE J560 are not electrically compatible with it and should be avoided in favour of proper J560 wiring.
How do heavy-truck plugs differ?
Heavy vehicles in North America are standardised through SAE J560, introduced in 1951, which means older heavy-duty vehicles may have other connectors. The plug is physically the same as the ISO 1185 connector, but J560 requires 12 volts and calls for larger wire sections to cope with the higher currents that 12 volts demands compared with 24. A few pins also do slightly different jobs, and pin 7 in particular needs attention. The functional differences are small. The voltage and current differences are what make the two incompatible without converters.
J560 does not control brakes. It is typically found on heavy trucks and trailers with pneumatic brakes, where all that is needed through the plug is power for the ABS unit and a brake light signal, while the brakes themselves work on air pressure.
| Connector | Region | Pins | Standard | Typical use |
|---|---|---|---|---|
| Flat 4-pin | North America | 4 | Accepted, not formal | Simpler trailers; US minimum signals |
| Round blade | North America | 7 | SAE J2863 | RVs and large trailers |
| Heavy-duty | North America | 7 | SAE J560 (12 V) | Trucks with air brakes |
| 12N | Europe | 7 | ISO 1724 (12 V) | Cars and light trucks |
| 13-pin | Europe | 13 | ISO 11446 (12 V) | Cars, caravans; replaced 12N+12S in 2008 |
| 24N | Europe | 7 | ISO 1185 (24 V) | Heavy trucks; replaced on newer vehicles |
| Heavy-duty | Europe | 15 | ISO 12098 (24 V) | Newer trucks and trailers |
What is the difference between a 7-pin and a 13-pin trailer plug?
In Europe both the 7-pin (ISO 1724) and the 13-pin (ISO 11446) are common, with the 13-pin being phased in. It is the newer design: it carries more services than the 7-pin, locks more positively and protects better against damp and dirt. Both are designed for 12-volt systems, though 7-pin plugs may exist on 6-volt and 24-volt vehicles. The 13-pin goes by the name Jaeger connector, after the company that developed it, and rare variants exist for 24 volts and for ADR use, differing in how they are keyed mechanically.
Colours are defined in ISO 4141-3, but the standard codes are not always followed and may differ on a particular vehicle. Older systems linger: vehicles and trailers with 6-volt systems can use a 7-pin or 5-pin plug, though they are rare now, and heavy trucks that run 12 volts tend to be older or from non-European markets.
The 7-pin 12N and its wiring traps
The 12N connector uses all 7 pins on newer trailers. Older trailers sometimes use a 5-wire arrangement in a 7-pin plug, in which case the pins for the right tail light (58R) and rear fog lamp (54G) go unused and all the tail lights hang from the left tail light pin (58L). Joining the right and left tail light pins can cause trouble on German cars, where standing lamps can be switched on on one side only.
Pin 2 (54G) has a history. Under DIN 72552 it was first intended for electrical control of trailer brakes. It has since been put to many uses: permanent +12 volts, +12 volts through the ignition lock, rear fog lights and reversing lights. That is why trailers are occasionally seen on the road with fog lights lit for no reason, the result of a vehicle wired for a live feed and a trailer wired for fog lamps.
Australia uses basically the same wiring except for pins 5 and 2. Pin 5 carries the trailer brake signal, so connecting an Australian trailer to a vehicle with ISO wiring means the trailer brakes will be applied as soon as the lights are turned on.
The 12S and the caravan supply
A second 7-pin connector, 12S (ISO 3732), supplements the 12N for the power supply that caravans need. It is used in Great Britain and may be found elsewhere in Europe. Its signals are not generally required by law, so connecting it is optional where the plug is present. The only change from the 12N is the centre pin, pin 7, which swaps gender so the two plug types cannot be confused: the 12S plug carries a pin where the 12N plug has a socket, and the outlet carries a socket where the 12N outlet has a pin.
There are two wiring variants, with a switchover date of 1999. The newer one adds a ground connection and shares battery charging with other consumers. A camper trailer from before 1999 with a battery, connected to a vehicle from after 1999, may therefore not charge. The 12N plus 12S pairing was replaced in 2008 by the single 13-pin ISO 11446 connector.
Older cars sometimes have a 5-pin ISO 1724 plug, laid out identically to the 7-pin but without pin 1 (L) and pin 4 (R). The wiring on vintage vehicles can differ completely from the standard, so measuring before connecting is sensible, and the plug or outlet can be swapped for a 7-pin when it needs replacing.
Are there other European connectors?
Yes. The NEN 6120 standard covers Multicon Feder and Multicon WeSt connectors (WeSt stands for Welt Standard), precursors to ISO 11446 designed to remain compatible with ISO 1724. A vehicle with one of these outlets should be able to take a trailer fitted with an ISO 1724 7-pin or 5-pin plug, provided the trailer coupling follows the standard and the plug casing is not made of metal, which would short the extra pins. Both share the same wiring and are found mainly in the Netherlands and Germany.
The DIAB/VBG family was developed by Djurle Industri AB for winters of snow, ice and road salt. These connectors can have an optional heating loop and are self-disconnecting, which reduces damage if a driver forgets to unplug when uncoupling or the trailer comes loose from the hitch. The 14-pin, 17-pin and 22-pin versions share the same physical dimensions but have different contact elements; the 17-pin serves where 14 is not enough, and the 22-pin extends it further. The 12-pin DIAB P12 is for 12-volt systems where standard ISO connectors fall short, built like a heavy-vehicle connector but smaller. The maximum current for the ground contact is 25A. They occur chiefly in Scandinavia, and suppliers also operate in Belgium, Great Britain and the United States.
How are heavy trailers connected in Europe?
Connections between a heavy trailer and its tractor unit are designated 24-volt. The 15-pin ISO 12098 connector is present on newer heavy commercial trucks and trailers and is intended to replace the pairing of ISO 1185 and ISO 3731 plugs, although not the ISO 7638 connector. A 13-pin predecessor looks nearly identical at a glance but has a different pin arrangement. It was uncommon, yet some vehicles may still carry one, and mixing the two up brings unpleasant results.
ISO 7638 is the brake electronics plug. The 7638-1 version serves 24-volt ABS and EBS on heavy trailers and is identified by a key tab on the outer ring by pin 5. The 7638-2 version serves 12-volt systems and has its key tab between pins 3 and 4. The old 7-pin 24N (ISO 1185) and 24S (ISO 3731) plugs are still common on heavy trucks and trailers but are replaced on newer vehicles by the 15-pin and the ISO 7638 connectors.
Can a European car tow a North American trailer?
Adapters are sold for exactly this. Most of them take the three-wire arrangement used in Europe, with 54, L and R, and combine turn signal and stop lamp into the two-wire system of L54 and R54 according to DIN, where one wire and one bulb on each side do both jobs. What these converters usually do not do is cope with a towing vehicle that keeps left and right position lights on separate circuits.
For those cars, which include many German models, the guidance is to feed the trailer tail lights from 58L and not to merge 58L with 58R, since that can cause problems in the towing vehicle. A more advanced fix uses two diodes to balance the load, provided they can handle high current or are used to switch a relay. For a trailer with many lights, a diode and relay arrangement is preferred; for one with a simple lighting set-up, wiring to 58L is usually enough.
Where this goes next
The direction of travel is already set out in the standards. In Europe the 13-pin ISO 11446 is being phased in, and it replaced the 12N plus 12S pairing in 2008. On heavy vehicles the 15-pin ISO 12098 is intended to replace the ISO 1185 and ISO 3731 combination on newer trucks and trailers. North America's light-vehicle plugs remain an accepted standard without a formal one, and SAE J560 dates from 1951.




